Rolling friction coefficient testing quantifies the resistance that materials generate when a rolling element moves under load over a counter-surface, delivering essential data for energy-efficiency design, tribological optimization, and quality control. This article explains the principles of rolling resistance measurement, typical sample types, key measurable parameters, recognized test methods and standards such as ISO 28580 and ASTM G115, and the industrial applications that depend on accurate rolling friction data.
Technical Overview
Rolling friction, also referred to as rolling resistance or rolling drag, is the force that opposes the motion of a body rolling on a surface under an applied normal load. Unlike sliding friction, which is dominated by adhesion and ploughing at the contact interface, rolling friction is driven mainly by internal hysteresis losses: as the rolling element deforms the contacting materials, energy is stored and only partially recovered during each rotation. The unrecovered energy is dissipated as heat and manifests as a measurable resistive force or torque.
The coefficient of rolling friction, commonly denoted as the rolling resistance coefficient Crr, is defined as the dimensionless ratio of the rolling resistance force Frr to the normal load N (Crr = Frr / N). Typical values are far lower than sliding coefficients: approximately 0.001 to 0.002 for hardened steel rolling elements in bearings or steel wheel-rail contact, 0.005 to 0.015 for pneumatic passenger car tires on smooth surfaces, and up to 0.03 or higher for soft polymer wheels on rough floors. Because rolling friction depends on both material properties and system geometry, standardized testing is essential for producing comparable, reproducible data.
Factors That Govern Rolling Friction
- Viscoelastic properties of the contacting materials, including storage modulus, loss modulus, and loss tangent (tan δ)
- Normal load and load distribution within the contact zone
- Radius of curvature and contact geometry of the rolling element
- Surface roughness, texture, and hardness of both contacting surfaces
- Rolling speed and effective contact time per revolution
- Temperature and thermal build-up during sustained rolling
- Lubrication condition, contamination, and ambient humidity
- Filler type and content in elastomer compounds, such as silica versus carbon black
Testing Samples
Accredited third-party laboratories and in-house material laboratories evaluate a wide range of sample forms, from standard test coupons to finished components. Specimens are normally conditioned in a controlled atmosphere, for example 23 ± 2 °C and 50 ± 5 % relative humidity in accordance with ISO 291, before testing begins.
Elastomers and Rubber Compounds
Tread compounds, sidewall rubbers, O-rings, and elastomeric rollers. Rubber is the most extensively tested material class for rolling resistance because viscoelastic hysteresis dominates its energy loss; specimens may be supplied as cured sheets, tread rings, or finished tires.
Polymers and Engineering Plastics
Injection-molded or machined wheels, casters, rollers, gears, and conveyor components produced from polyamide (PA), polyoxymethylene (POM), polyurethane (PU), polyethylene (PE), and their glass-fiber or carbon-fiber reinforced grades.
Metals and Alloys
Through-hardened bearing steels, rail steels, wheel steels, and nonferrous alloys evaluated as balls, cylinders, rings, or finished raceway samples to characterize rolling friction and rolling contact behavior under representative loads and speeds.
Ceramics, Composites, and Coated Surfaces
Silicon nitride and zirconia rolling elements, carbon-fiber-reinforced polymer (CFRP) laminates, PVD or CVD coated discs, and resilient floor coverings that must meet defined rolling behavior requirements for casters and wheels.
Finished Components and Assemblies
Complete pneumatic or solid tires, industrial casters, luggage and trolley wheels, slewing rings, and rolling bearings tested in as-delivered condition, reflecting actual production geometry, material state, and surface finish.
Testing Items
Rolling friction test programs are typically structured around the following measurable parameters:
- Coefficient of rolling friction, or rolling resistance coefficient (Crr, dimensionless)
- Rolling resistance force (N) at defined load, speed, and inflation pressure
- Rolling resistance torque (N·m) and frictional power loss (W)
- Energy loss per revolution or per unit distance traveled (J/rev, J/m)
- Load sensitivity exponent describing how resistance force varies with normal load
- Speed dependence of rolling resistance across a defined velocity range
- Temperature dependence and thermal build-up behavior during sustained rolling
- Breakaway (starting) rolling resistance and low-speed rolling characteristics
- Supporting viscoelastic indicators such as loss tangent (tan δ) at rolling-relevant temperatures and frequencies
Testing Methods
Drum (Rotating Cylinder) Method — ISO 28580
The specimen tire is pressed against a large rotating steel drum, typically 2 m in diameter, at a reference speed of 80 km/h while the reaction force on the spindle is measured with calibrated load cells. The result is corrected for drum curvature, parasitic losses, and warm-up effects to yield a standardized force value. This single-point method underpins tire rolling resistance labeling schemes in many markets and supports conformity assessment aligned with UN ECE Regulation No. 117.
Multi-Point and Coastdown Methods — ISO 18164, SAE J1269, SAE J2452
Multi-point procedures measure rolling resistance over a matrix of speeds, loads, and inflation pressures. The trailer method tows instrumented test wheels at constant speed and records the resisting force, while the stepwise coastdown method derives resistance from the deceleration of a freely rolling test mass, enabling coefficient mapping across realistic operating ranges.
Inclined Plane and Free-Rolling Distance Methods
Suitable for rigid materials and coated surfaces, a sphere or roller is released on a calibrated incline and allowed to decelerate over a flat track. The ratio of horizontal travel distance to release height provides an effective rolling friction coefficient, offering a simple and cost-efficient screening technique for material ranking.
Instrumented Tribometer Rolling Modules
Ball-on-disc or roller-on-flat modules apply a defined normal load and record friction torque continuously through load cells or torque transducers. Test reporting can follow the general friction-measurement guidance of ASTM G115, and elastomer specimen preparation may reference the frictional-property practices of ISO 15113 adapted to rolling contact. These rigs permit controlled variation of load, speed, temperature, and lubrication for research-grade characterization.
Bearing Friction Torque Measurement
Finished bearings are operated on dedicated rigs at specified axial and radial loads and speeds while starting and running torque are recorded, separating the contributions of rolling elements, cage, lubricant, and seals. The resulting data support power-loss budgeting in precision machinery and drivetrains.
Control of Standard Test Conditions
- Specimen conditioning in a standard atmosphere, for example 23 °C and 50 % relative humidity per ISO 291
- Defined warm-up period before data acquisition to reach steady-state temperature
- Calibrated load cells, speed sensors, and temperature instrumentation with traceable calibration
- Parasitic-loss compensation for bearing, air drag, and drum losses
- Curvature correction when a drum replaces a flat road or floor surface
- Repeatability verification through replicate runs and periodic reference specimen checks
Applications
Tire Development and Regulatory Labeling
Rolling resistance accounts for a substantial share of vehicle energy consumption at constant speed. Tire manufacturers use drum-method data for compound development, benchmarking, and fuel-efficiency labeling classes, with GB/T 18861 serving as the corresponding national method in the Chinese market alongside ISO 28580.
Bearings, Drivetrains, and Precision Machinery
Low rolling friction directly improves mechanical efficiency and reduces heat generation in machine-tool spindles, electric motors, gearboxes, and robotics, making friction torque data a key selection and qualification criterion for components and lubricants.
Material Handling, Logistics, and Conveyor Systems
Caster wheels, conveyor rollers, and wheel-on-floor interactions are optimized to reduce push and pull forces, protect flooring, and satisfy ergonomic handling limits in warehouses, airports, and hospitals.
Railway and Heavy-Duty Transport
Wheel-rail rolling resistance influences traction energy demand, wheel wear, and maintenance planning, and material characterization supports rail steel selection and lubrication strategy.
Medical Equipment, Furniture, and Consumer Products
Hospital beds, trolleys, office chairs, luggage, and sports equipment such as skateboards, inline skates, and precision ball bearings all depend on qualified low rolling friction for smooth, safe, and durable performance.
Materials R&D and Coating Qualification
Rolling friction data support the development of low-hysteresis elastomer formulations, self-lubricating polymers, and low-friction coatings, and are frequently combined with dynamic mechanical analysis and rolling contact fatigue testing for complete tribological assessment.
FAQ
How does the rolling friction coefficient differ from the sliding friction coefficient?
Sliding friction arises mainly from adhesion and ploughing between surfaces in relative sliding, whereas rolling friction is dominated by viscoelastic hysteresis and micro-slip within the rolling contact. As a result, rolling coefficients are typically one to two orders of magnitude lower than sliding coefficients and respond differently to load, speed, and temperature.
Which standards govern rolling friction testing?
For tires, ISO 28580 (single-point drum method), ISO 18164 (multi-point methods), SAE J1269, SAE J2452, and GB/T 18861 define the principal procedures, with UN ECE Regulation No. 117 referencing them for conformity assessment. General friction measurement and reporting practice is covered by ASTM G115, and elastomer friction specimen practice by ISO 15113.
What sample forms can be tested?
Specimens range from cured rubber plates, tread rings, and polymer discs to steel and ceramic balls or rollers, coated flats, and finished products such as tires, casters, and bearings. Accredited third-party laboratories can advise on minimum sample dimensions, quantities, and conditioning requirements for each method.
Why is temperature control so important?
Elastomer rolling resistance is strongly temperature-dependent because hysteresis losses track the viscoelastic loss factor of the material. Standardized warm-up periods and controlled ambient conditions ensure that measured values are reproducible and comparable between laboratories.
What typical values can be expected?
The rolling resistance coefficient is approximately 0.001 to 0.002 for precision ball bearings and steel wheel-rail contact, 0.005 to 0.015 for modern passenger car tires, and 0.02 to 0.05 or higher for soft polymer wheels on rough or compliant floors. Values vary with load, speed, and surface pairing, which is why standardized test conditions are essential.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing