REACH testing methods are the analytical procedures used to verify that products placed on the European Union market comply with Regulation (EC) No 1907/2006, including screening for Substances of Very High Concern (SVHC) and Annex XVII restricted substances. This technical guide explains the standard laboratory techniques—from ICP-OES and GC-MS to wet-chemical migration testing—that accredited third-party laboratories apply to polymers, textiles, metals, and electronic components. Read on to learn how REACH testing works, which sample types and testing items are covered, and how manufacturers can maintain continuous compliance.
Technical Overview
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) is Regulation (EC) No 1907/2006 of the European Union and one of the most comprehensive chemicals legislations in the world. While registration duties primarily target manufacturers and importers of chemical substances and mixtures, producers and importers of finished articles must ensure that their products do not contain Substances of Very High Concern (SVHC) above 0.1% weight-by-weight (w/w) or substances whose use is restricted under Annex XVII. REACH testing methods are the analytical procedures used by accredited third-party laboratories to verify this compliance through chemical analysis of materials and components.
The regulatory framework relevant to article testing consists of three pillars:
- Candidate List of SVHCs: substances identified by the European Chemicals Agency (ECHA) as carcinogenic, mutagenic, reprotoxic, persistent, bioaccumulative, toxic, or of equivalent concern. If an SVHC is present above 0.1% w/w, suppliers must communicate information down the supply chain, and importers may be obliged to notify ECHA or submit data to the SCIP database under the Waste Framework Directive.
- Annex XIV (Authorisation List): SVHCs whose use requires explicit authorisation after a specified sunset date.
- Annex XVII (Restrictions): substance-specific limits and bans applicable to consumer articles, such as nickel release, azo colorants, cadmium, lead, phthalates, PAHs, and organotin compounds.
ECHA updates the Candidate List approximately twice per year, and it now contains well over 240 entries. Because the list evolves continuously, REACH testing is not a one-time event but an ongoing verification program integrated into product compliance management.
Testing Samples
REACH testing is performed on homogeneous materials, meaning each analyzed portion must consist of a single material that cannot be mechanically disjointed into different components. Typical sample categories include:
Polymers and Plastics
PVC, polyolefins, ABS, elastomers, and rubber compounds are screened for phthalate plasticizers, halogenated flame retardants, short-chain chlorinated paraffins, PAHs in rubber goods, and SVHC monomers or additives. Samples are usually cut, cryo-milled, and homogenized before extraction.
Textiles and Leather
Natural and synthetic fibers, coated fabrics, and leather are tested for restricted azo dyes, formaldehyde, pentachlorophenol, chromium VI in leather, perfluorinated compounds, and chlorinated paraffins. Dyed and printed areas are analyzed separately from undyed base materials.
Metals and Coated Articles
Metal alloys, coatings, platings, and solder are analyzed for lead, cadmium, and nickel release. Conversion coatings on zinc and aluminum surfaces are specifically evaluated for hexavalent chromium.
Electrical and Electronic Products
Cables, housings, printed circuit boards, connectors, and plastic components are tested for SVHC plasticizers, flame retardants, and regulated elements, following the homogeneous-material dissection principles established in the EN IEC 62321 series.
Coatings, Paints, Inks, and Adhesives
Liquid and cured formulations are assessed for SVHC solvents, bisphenols, phthalates, and heavy-metal pigments.
Toys and Childcare Articles
These products attract heightened scrutiny and are additionally evaluated for element migration using methods aligned with EN 71-3, alongside standard SVHC screening.
Testing Items
Testing scopes generally fall into two categories: full SVHC screening against the current Candidate List, and targeted quantitative testing for Annex XVII restricted substances. Common testing items include:
- SVHC full screening: typically more than 240 substances covering phthalates, bisphenols, phenolic compounds, flame retardants, solvent stabilizers, and metal compounds.
- Phthalates: DEHP, DBP, BBP, DIBP, DINP, DIDP, DNOP, and related esters used as plasticizers.
- Heavy metals: lead, cadmium, mercury, total chromium, hexavalent chromium, arsenic, and nickel release from articles in prolonged skin contact.
- Azo colorants: reductive cleavage to restricted carcinogenic aromatic amines in textiles and leather.
- Polycyclic aromatic hydrocarbons (PAHs): the REACH-relevant PAHs, including benzo[a]pyrene, in rubber and plastic components touching the skin.
- Chlorinated paraffins: short-chain and medium-chain chlorinated paraffins used as flame retardants and plasticizers.
- Flame retardants: PBDEs, HBCDD, TBBPA, tris(2-chloroethyl) phosphate, and related halogenated compounds.
- Organotin compounds: TBT, DBT, MBT, DOT, and TPhT in PVC, textiles, and silicone products.
- Formaldehyde: free and released formaldehyde in textile and leather articles.
- Perfluorinated compounds: PFOA, PFOS, and related PFAS used for water and grease repellency.
- Dimethyl fumarate (DMF): anti-mold agent banned in articles contacting skin.
Testing Methods
REACH testing combines sample preparation, extraction or digestion, and instrument-based quantification. The choice of method depends on the analyte class, matrix, and whether total content or migration is regulated.
Sample Preparation and Homogenization
Articles are disassembled into homogeneous materials, which are then cut, ground, or cryogenically milled to increase surface area and ensure representative extraction. Particle size and homogeneity directly influence recovery and reproducibility.
Rapid Screening by XRF
X-ray fluorescence spectrometry provides fast, non-destructive screening for elemental contaminants such as lead, cadmium, mercury, bromine, and chlorine. Positive XRF results are confirmed using destructive elemental techniques.
Elemental Analysis by ICP-OES and ICP-MS
Metals are quantified after acid digestion, typically microwave-assisted, using inductively coupled plasma optical emission spectrometry (ICP-OES) or inductively coupled plasma mass spectrometry (ICP-MS). Established procedures include the digestion and measurement protocols in the EN IEC 62321 series for electronic assemblies and EN 1122 for cadmium in plastics. Detection limits in the low mg/kg range comfortably support the 0.1% w/w SVHC threshold and the stricter Annex XVII limits.
GC-MS Analysis of Semivolatile Organics
Gas chromatography–mass spectrometry is the workhorse for phthalates, PAHs, organotin compounds after derivatization, flame retardants, and chlorinated paraffins. Samples undergo solvent extraction with appropriate solvents, followed by GC-MS quantification against calibrated standards. Chlorinated paraffins in leather can be determined according to ISO 18219, and phthalates in childcare items according to EN 14372.
HPLC and LC-MS/MS Techniques
Azo dyes are analyzed after reductive cleavage in a citrate-buffered solution, with liberated aromatic amines quantified by HPLC-DAD or GC-MS in line with EN 14362-1 and EN 14362-3. Bisphenol A, phenolic SVHCs, and perfluorinated compounds are determined by HPLC with fluorescence or mass-spectrometric detection (LC-MS/MS), which offers high sensitivity and selectivity for polar, thermolabile analytes.
Migration and Release Testing
Where REACH regulates release rather than total content, simulative extraction methods are applied: nickel release is measured after one week in synthetic sweat according to EN 1811, with wear-and-corrosion pre-treatment of coated items per EN 12472; hexavalent chromium in leather is determined by colorimetric or chromatographic methods per EN ISO 17075-1; formaldehyde in textiles is quantified after water-bath extraction per EN ISO 14184-1; and element migration from toys follows EN 71-3 with gastric-intestine simulant solutions.
For SVHC screening, laboratories typically target a limit of quantification at or below 100 mg/kg (0.01% w/w), providing a tenfold safety margin against the 0.1% reporting threshold. Results are reported per homogeneous material with clear identification of the tested component.
Applications
REACH testing is applied across the product lifecycle wherever goods are manufactured for, or imported into, the European Economic Area. Key applications include:
- EU market access: demonstrating that consumer products, electronics, toys, textiles, footwear, and jewelry meet SVHC and Annex XVII requirements before customs clearance and placement on the market.
- Importer due diligence: providing the analytical evidence EU importers need to fulfill information and notification obligations toward ECHA and the SCIP database.
- Supply chain communication: generating the substance data required for Article 33 SVHC information transfer along the supply chain to downstream users and consumers.
- Material and supplier qualification: verifying incoming plastics, dyes, coatings, and chemicals during product development and vendor audits.
- Ongoing quality control: periodic re-screening after each Candidate List update or material change, and root-cause investigation in case of market surveillance actions or recall claims.
FAQ
What is the difference between REACH SVHC testing and REACH registration?
REACH registration applies to companies that manufacture or import chemical substances in quantities above one tonne per year and involves dossier submission to ECHA. SVHC testing, by contrast, is chemical analysis of finished articles or components to verify whether listed substances exceed the 0.1% w/w threshold. Most product manufacturers and article importers only need testing and communication, not registration.
Is REACH testing legally mandatory?
There is no blanket legal obligation to test every article, but market surveillance authorities can demand evidence of compliance, and only analytical testing can conclusively demonstrate that SVHCs are absent or below thresholds. Importers who cannot supply valid data risk border rejection, withdrawal orders, and penalties under national enforcement laws.
How much sample is required and how long does testing take?
Typical requirements are 10–30 grams or 10–30 square centimeters per homogeneous material, depending on the testing scope. Standard turnaround for full SVHC screening is five to ten working days; targeted single-item tests are usually faster. Only one material of each type per product usually needs testing.
How often should SVHC screening be repeated?
The Candidate List is updated approximately twice per year. Best practice is to review test reports after every update, re-test when newly listed substances plausibly occur in the product, and re-verify whenever materials, formulations, or suppliers change.
How does REACH differ from RoHS?
RoHS restricts ten specific substance groups in electrical and electronic equipment with fixed concentration limits, whereas REACH covers all article categories, contains a much longer and growing substance list, and imposes communication and notification duties above the 0.1% w/w threshold. The two regulations are complementary, and electronic products are commonly tested against both.
What does a non-detect result mean?
A result below the limit of quantification indicates the substance was not present above the method sensitivity, typically 100 mg/kg or lower for SVHC screening. This supports a compliance conclusion well below the 0.1% threshold, provided the tested sample is representative and the report reflects the current Candidate List.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing