PEEK melt mold-filling expansion analysis is a specialized rheological and molding evaluation that quantifies how polyetheretherketone melt swells and deforms as it is injected through nozzles, runners, and gates into a mold cavity. By measuring die swell ratio, shear viscosity, PVT behavior, and actual cavity-filling performance, this analysis enables accurate gate sizing, runner balancing, shrinkage prediction, and reliable injection molding simulation for high-precision PEEK components. This article explains the technical principles, sample types, testing items, standard test methods, and industrial applications of PEEK melt expansion analysis.
Technical Overview
PEEK (polyetheretherketone) is a semi-crystalline, high-performance engineering thermoplastic with a glass transition temperature of approximately 143 °C and a melting point of approximately 343 °C, and it is typically processed at melt temperatures between 360 °C and 400 °C. During injection molding, the PEEK melt is subjected to intense shear as it flows through the nozzle, sprue, runners, and gates. Because PEEK is a viscoelastic fluid with relatively high molecular weight, a portion of the deformation energy is stored elastically in the molecular chain network. When the melt exits a restricted flow channel and enters a larger cross-section, this stored elastic energy is recovered, causing the melt stream to expand perpendicular to the flow direction. This phenomenon is known as die swell, extrudate swell, or the Barus effect, and it directly governs mold-filling expansion behavior.
Melt expansion analysis distinguishes two coupled but distinct mechanisms. The first is elastic swell, which occurs within milliseconds at the gate and runner exits and depends on shear rate, melt temperature, molecular weight distribution, channel geometry (L/D ratio and entrance angle), and filler content. The second is thermally driven volumetric shrinkage, which occurs later during cooling and crystallization in the cavity. Accurately separating and quantifying both effects is essential for gate sizing, runner balancing, flash prevention, weld line positioning, packing pressure optimization, and dimensional tolerance control. Die swell is commonly expressed as the swell ratio B, defined as the extrudate diameter divided by the capillary or gate diameter, or as an equivalent cross-sectional area ratio.
For unfilled PEEK, elastic swell can be significant at high injection speeds and can produce jetting, gate blush, or localized overpacking near the gate. Reinforced grades containing glass fiber or carbon fiber exhibit markedly lower swell because rigid fibers suppress elastic recovery of the matrix, but they introduce anisotropic shrinkage instead. A systematic melt expansion analysis therefore combines capillary rheometry, melt flow testing, PVT measurement, molding trials, and simulation model calibration into a complete characterization package.
Testing Samples
Virgin Unfilled PEEK Resins
Natural, unfilled PEEK pellets in their as-received drying state are tested to establish the baseline rheological and expansion behavior of the polymer matrix. These samples are dried according to the manufacturer's recommendations, typically 3 to 5 hours at 150 °C, to eliminate moisture-induced artifacts such as hydrolytic viscosity loss and bubble formation in the extrudate.
Reinforced and Modified PEEK Compounds
Common sample types include 30 % glass-fiber-reinforced PEEK, 30 % carbon-fiber-reinforced PEEK, and tribological grades containing PTFE, graphite, or carbon powder. Fiber-reinforced samples are evaluated specifically to quantify the suppression of die swell and to capture fiber orientation effects on cavity expansion and anisotropic dimensional change.
Specialty and Process-Affected Materials
Medical-grade PEEK intended for implantable or surgical components, electrically conductive or static-dissipative grades, pigmented compounds, regrind-containing formulations, and thermally reprocessed materials can all be analyzed. Comparing reprocessed material against virgin resin through melt expansion testing is an effective way to detect chain degradation, which appears as reduced viscosity and altered swell behavior.
Testing Items
A comprehensive PEEK melt expansion analysis typically covers the following measurable parameters:
- Die swell ratio (extrudate diameter or area ratio) as a function of shear rate, melt temperature, and die geometry
- Apparent and true shear viscosity curves across shear rates from approximately 100 s⁻¹ to 10,000 s⁻¹
- Entrance pressure losses and Bagley correction data for separating elastic and viscous contributions
- Melt flow rate (MFR) and melt volume flow rate (MVR) for lot-to-lot quality control
- Melt density and PVT (pressure–volume–temperature) behavior for packing and shrinkage simulation
- Thermal characterization, including melting point, crystallization temperature, crystallinity, and crystallization kinetics under realistic cooling rates
- Thermal stability indicators, such as viscosity drift or mass loss during extended residence at processing temperature
- Actual mold-filling expansion data from short-shot and spiral flow trials, including gate swell, flow front velocity, and cavity pressure response
- Molding shrinkage and post-molding shrinkage of molded specimens for correlation with rheological results
Testing Methods
Capillary Rheometry with Die Swell Measurement
Capillary rheometry is performed in accordance with ISO 11443 or ASTM D3835 using a high-temperature rheometer equipped with capillary dies of multiple L/D ratios, for example 10/1, 20/1, and short orifice dies for Bagley end corrections. The barrel is held at temperatures between 360 °C and 420 °C, and steady-state extrusion is conducted at a matrix of shear rates spanning typical injection speeds. A non-contacting laser diameter gauge positioned at the die exit records the extrudate diameter online, allowing the die swell ratio to be captured before gravity and cooling distort the strand. Rabinowitsch correction converts apparent to true shear rate, and Bagley correction removes entrance pressure effects so that the purely elastic component of swell can be isolated.
Melt Flow Rate Testing
MFR and MVR are determined per ISO 1133-1 or ASTM D1238, method A or method B, using a test temperature appropriate for PEEK, commonly 400 °C with a defined nominal load. While melt flow rate does not directly measure swell, it provides a rapid viscosity index that is cross-referenced with capillary data to verify sample consistency and to screen for thermal degradation.
PVT and Melt Density Analysis
Specific volume as a function of temperature and pressure is measured per ISO 17744 using a confined, pressure-controlled dilatometer. PVT data define the melt compressibility and solidification transition that, combined with the elastic swell ratio, allow accurate prediction of part weight, packing efficiency, and volumetric shrinkage in cavity-filling calculations.
Mold-Filling Trials and Short-Shot Analysis
Instrumented injection molding trials are conducted per the principles of ISO 294-1 using spiral flow molds, stepped-cavity molds, or production-representative tooling with cavity pressure transducers and thermocouples. Progressive short shots visualize the flow front, gate jetting, gate swell, and the actual expanded flow channel thickness achieved after the melt passes the gate. These empirical results quantify real mold-filling expansion under production-relevant conditions and serve as ground-truth data.
Thermal and Degradation Characterization
Differential scanning calorimetry per ISO 11357 determines melting, crystallization, and crystallinity, which control the shrinkage component that coexists with elastic expansion. Thermogravimetric analysis per ISO 11358 assesses thermal stability at processing temperatures, confirming that measured swell values are not corrupted by degradation-driven viscosity changes.
Simulation Model Calibration
The measured viscosity curves, PVT data, thermal properties, and die swell ratios are used to fit Cross-WLF or Carreau-Yasuda viscosity models and, where required, viscoelastic constitutive models in injection molding simulation software. Predicted filling patterns, gate swell, pressure traces, and shrinkage are then validated against the molding trial data. This closed-loop calibration produces simulation models that can reliably forecast melt expansion behavior for new tooling designs.
Applications
Melt expansion analysis of PEEK supports engineering decisions across demanding industries:
- Medical devices and implants: precise gate and runner design for trauma plates, spinal cages, and surgical instruments where tight dimensional tolerances and ISO 10993-compliant materials are required
- Aerospace: mold and process development for brackets, insulators, seals, and structural clips that must meet flame, smoke, and toxicity expectations aligned with applicable FAR and UL 94 requirements
- Semiconductor manufacturing: dimensionally stable wafer-handling components, CMP retainers, and test sockets where gate blush and localized swell defects cannot be tolerated
- Oil and gas: high-pressure sealing components, bearings, and downhole electrical insulators that require defect-free filling at high injection pressures
- Automotive: thrust washers, gearbox components, and sensor housings with controlled shrinkage and warpage
- Material development and quality control: comparing swell and viscosity signatures for new compounds, evaluating regrind content, and certifying incoming resin lots in accredited third-party laboratories
FAQ
What exactly is die swell, and why does PEEK exhibit it?
Die swell is the elastic expansion of a polymer melt after it exits a restricted channel such as a gate or capillary. Under high shear, PEEK molecular chains are stretched and oriented, storing elastic energy. Once the constraining die wall is removed, the chains recoil and the melt expands. Because PEEK is processed at high temperatures and high shear rates with a relatively stiff molecular backbone, quantifying this swell is critical for accurate mold-filling prediction.
How is the die swell ratio calculated?
The swell ratio B is the diameter of the extrudate divided by the diameter of the die, or equivalently the square root of the corresponding area ratio. A laser micrometer at the die exit measures the extrudate diameter immediately after extrusion. Testing is repeated across a range of shear rates and temperatures because swell increases strongly with shear rate and decreases with higher melt temperature.
How do glass and carbon fibers affect PEEK melt expansion?
Rigid fibers mechanically restrain elastic recovery of the polymer matrix, so 30 % glass-fiber or carbon-fiber PEEK grades show substantially lower die swell than unfilled resin. However, fibers introduce fiber orientation and anisotropic shrinkage, so the expansion analysis is expanded to include directional shrinkage measurement and fiber orientation assessment.
Is melt expansion the same as shrinkage?
No. Expansion is an instantaneous elastic effect that occurs as melt exits the gate and enters the cavity. Shrinkage is a slower volumetric contraction driven by cooling, melt compressibility, and crystallization. Both affect final dimensions, and a complete analysis measures each mechanism separately using rheometry, PVT data, and molded-specimen shrinkage testing per ISO 294-4.
How are the results used in mold and process design?
Measured swell ratios and viscosity curves guide gate sizing, gate land length, runner diameter, and the selection of injection velocity profiles to avoid jetting and flash. The data feed calibrated simulation models that predict filling patterns, packing pressure requirements, weld line locations, and final part dimensions, reducing tooling iterations and validation time. Testing is carried out in accredited third-party laboratories following ISO and ASTM methods, or in conjunction with in-house molding trials, depending on project scope.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing