Lead screw torque measurement testing quantifies the driving torque, drag torque, and preload torque characteristics of ball screws, trapezoidal lead screws, and roller screws under controlled rotational and axial loading conditions. The experiment verifies friction behavior, preload uniformity, and mechanical transmission efficiency against reference standards such as ISO 3408, JIS B 1192, and GB/T 17587. This article explains the testing principle, sample requirements, instrumentation, test procedures, and typical industrial applications of lead screw torque determination.
Technical Overview
Lead screw torque measurement testing is an experimental procedure used to determine the torque required to rotate a lead screw under defined conditions of speed, preload, lubrication, and axial load. The measured torque directly reflects the friction conditions among the screw shaft, the rolling or sliding load-transfer elements, and the nut, making it a primary indicator of manufacturing quality, assembly integrity, and expected service performance.
Excessive or unstable torque signals problems such as poor thread grinding quality, incorrect preload setting, contamination, misalignment, or inadequate lubrication. Conversely, torque that is abnormally low may indicate insufficient preload and reduced system rigidity. Torque data are therefore used both for acceptance testing of finished products and for statistical process control during manufacturing.
The principal reference standards for this test include:
- ISO 3408 series – Ball screws: acceptance conditions and acceptance tests, including preload drag torque evaluation
- JIS B 1192 – Japanese standard for ball screws, technically aligned with ISO 3408
- GB/T 17587 series – Chinese national standard for ball screws, consistent with ISO 3408
- DIN 69051 – German standard covering ball screw assemblies
- ISO 2901, ISO 2902, ISO 2903 – ISO metric trapezoidal screw thread standards applicable to sliding lead screws
Testing Samples
Ball Screws
Ground or rolled precision ball screws with single or double nuts, including preloaded double-nut and oversized-ball configurations. Typical specimens range from small diameters of approximately 6 mm to large machine-tool sizes of 125 mm, with shaft lengths from a few centimeters up to several meters, supplied with the matching nut and any wiper or seal components.
Trapezoidal and Acme Lead Screws
Sliding-friction screws with trapezoidal thread profiles paired with bronze, engineered polymer, or steel nuts. These specimens are commonly tested to determine the effective friction coefficient, forward efficiency, and self-locking behavior.
Planetary Roller Screws
High-load-capacity roller screws with planetary thread-rolling elements, evaluated for no-load drag torque, preload torque, and torque uniformity in heavy-duty actuation applications.
Complete Actuator Sub-Assemblies
Screw units delivered with support bearings, nut housings, and end fittings may be tested as built, so that system-level torque losses from bearings and seals are captured together with the screw-nut torque itself.
Testing Items
- No-load running torque (dynamic drag torque) measured over the full travel length
- Starting (breakaway) torque at the beginning of rotation
- Preload drag torque and its permissible variation band
- Torque ripple and per-revolution torque fluctuation
- Directional torque difference between forward and reverse rotation
- Load-dependent drive torque and torque-to-load linearity
- Mechanical transmission efficiency in both forward and reverse directions
- Equivalent friction coefficient derived from measured torque
- Influence of lubrication condition, temperature, and run-in history on torque
Testing Methods
Specimen Preparation and Mounting
The screw shaft is supported between centers or clamped in a rigid fixture with the nut constrained against rotation. The drive end of the shaft is coupled through a calibrated rotary torque transducer to a servo motor or geared drive unit. Specimens are cleaned, lubricated with the specified grease or oil, and pre-conditioned by several travel cycles before formal data acquisition to stabilize the friction state.
Dynamic No-Load Torque Test
The screw is rotated at a specified speed, commonly 100 rpm or a customer-designated value, without any external axial load while the torque transducer continuously records instantaneous torque. Data are acquired across at least several complete nut travels. The mean torque, maximum and minimum values, and torque ripple are reported together with a torque-versus-travel curve, which reveals local defects such as thread errors or damaged rolling elements.
Preload Drag Torque Test
For preloaded ball screws, the average drag torque is measured under zero external load and compared with the reference value calculated from the specified preload force and lead, using the approximate relationship:
Tp = k × Fp × Ph / (2π)
where Fp is the preload force, Ph is the screw lead, and k is a design factor, typically about 0.1 for conventional double-nut preloaded ball screws. Acceptance per ISO 3408-3 or GB/T 17587.3 requires the measured mean torque to fall within the tolerance band defined by the standard or the customer drawing.
Efficiency Determination under Axial Load
A controlled axial load is applied to the nut using dead weights, a pneumatic cylinder, or an electromagnetic loader while torque and displacement are recorded simultaneously. The forward transmission efficiency is calculated as:
η = F × Ph / (2π × T)
where F is the applied axial force, Ph is the lead, and T is the measured driving torque. Reverse efficiency and backdriving behavior may be evaluated by applying axial force to a freely rotatable screw, which is particularly important for confirming the self-locking capability of trapezoidal lead screws.
Instrumentation and Accuracy Requirements
Calibrated strain-gauge or digital rotary torque transducers with accuracy classes of 0.1 % to 0.5 % of full scale are used together with rotary encoders for speed and angle measurement and load cells for axial force. Ambient temperature, lubricant type, and prior operating history are recorded because these factors measurably influence torque. All measurement chains must be traceable to national or international metrology standards, and testing is typically performed in accredited third-party laboratories or calibrated in-house facilities.
Applications
- Acceptance inspection of ball screws for CNC machine tools, machining centers, and grinding machines
- Production quality control for thread grinding accuracy, nut preloading, and assembly consistency
- Motor sizing and drive design based on measured drive torque, duty cycles, and efficiency maps
- Verification of self-locking performance in sliding lead screw mechanisms for lifting and positioning equipment
- End-of-line functional testing of electric cylinders and electromechanical linear actuators
- Fitness-for-service assessment of screws after field operation, extended storage, or refurbishment
- Comparative research on lubricants, surface coatings, and alternative nut materials
- Qualification of screw drives for automotive electric power steering, aerospace actuation, medical devices, and semiconductor manufacturing equipment
FAQ
What is lead screw torque measurement testing?
It is an experiment that measures the torque required to rotate a lead screw under controlled speed, load, and lubrication conditions in order to evaluate friction behavior, preload setting, transmission efficiency, and overall product quality.
Which standards govern the test?
Ball screws are normally tested to ISO 3408 or its technical equivalents, JIS B 1192 and GB/T 17587. Trapezoidal lead screws are typically evaluated against the ISO 2901, ISO 2902, and ISO 2903 thread standards together with customer-specific torque specifications.
What is the difference between no-load torque and preload drag torque?
No-load running torque is the total torque needed to turn the complete assembly without external axial load, including contributions from seals and bearings. Preload drag torque is the specific component attributable to internal preload, which ISO 3408-3 standardizes as the acceptance parameter for preloaded ball screws.
How should samples be prepared and submitted?
Samples should be clean, complete with nut and any sealing components, lubricated as specified, and accompanied by drawing information including nominal diameter, lead, accuracy grade, preload force, and any applicable torque limits.
What torque uniformity is typically acceptable?
Acceptance limits depend on the accuracy class and manufacturer specification. In common practice, the measured mean preload drag torque must lie within the tolerance band around the calculated reference torque, and the peak-to-mean torque ripple is usually restricted to a limited percentage of the mean value.
Can the test determine transmission efficiency?
Yes. By applying a known axial load and measuring the corresponding driving torque, the forward efficiency is computed directly from the relation η = F × Ph / (2π × T), and reverse efficiency can be obtained through backdriving measurement.
How long does a typical test take?
A standard no-load and preload drag torque test, including mounting, conditioning, and data acquisition, typically requires one to three hours. Loaded efficiency mapping, temperature studies, and extended torque monitoring programs require additional time depending on the test plan.
Why Choose ZKGX?
- State-of-the-art analytical equipment
- Highly qualified scientific team
- Fast turnaround time
- Competitive pricing